Home » Categories » DIY » Projects

A New Patio From The Ground Up

A New Patio From The Ground Up

Does your patio look tatty and uninviting? This rebuild will inspire you to get the party cooking.

What you need to install the pavers

Smartstone Estcourt pavers (500 x 500mm), sandstone
Smartstone Huguenot cobblestone,sandstone
PPC Cement
River sand

What To Do

Step 1: Clear the area of all existing paving and grass, making sure that it is level and slopes very gently away from the house to allow for water runoff.

Step 2: Mix together six wheelbarrows of river sand with two bags of PPC Cement and enough water to form a semi-wet mixture. Spread this over the levelled area with a long piece of wood. Check the levels before placing the pavers. Make sure that all the mixed cement is used within an hour. Mix more as required.

Step 3: Lay the pavers on the wet cement mixture and tap them into place using a rubber mallet. Use builders line and pegs to make sure all the pavers are in a straight line and check every paver with a spirit level to make sure it is level. Allow a 10mm gap between the pavers for the grouting – tile spacers make this job easier and more accurate.

Step 4: Once all the tiles have been laid finish the edge with a row of cobblestones using the same method as with the tiles. Smartstone cobbles come with a lug on two sides allowing you to bump the cobbles up against each other, leaving a consistent gap between each of them.
 

What you need for grouting

Cement
Plaster sand

What To Do

Mix three parts of plaster sand with one part cement and water to form a thick cement grout. Apply this mixture to small areas at a time with a squeegee, filling in the gaps between the pavers and the cobbles. Clean off excess grout with a damp sponge as you go. Leaving cement to dry on the pavers can alter their colour and can be hard to remove later.

Materials needed to install the Heatwave Braai

Octo De Luxe Heatwave braai
Sikaflex®-11 FC + sealant
Rawl bolts

What to do

The Heatwave freestanding braai is very easy to install. Make sure you have a solid, level surface to work on and rawl bolt the framework to the floor. The flue is then attached to the top of the braai using Sikaflex®-11 FC + sealant.

Adding the finishing touches

Wall decoration
Sikaflex®-11 FC + sealant
Homewood furniture – we used a table and benches from the Paindane range and Mixed Wood Cubes

What to do

To bond the decorative hearts onto the wall make sure that the surface is clean and dry. Place the Sikaflex®-11 FC+ in spots at intervals of a few centimetres on the back of the hearts 3cm in diameter and approximately 0.4cm thick. Press each ornament onto the wall and hold it in position for a few minutes. If necessary, use props to hold the ornaments in place while the Sikaflex®-11 FC+ is left to cure for 24 to 48 hours.
 
Attachments Attachments
There are no attachments for this article.
Comments (1) Comments
Comment by Heather on Tue, Jun 19th, 2012 at 8:34 PM
A before pic of the ‘tatty‘ patio would be really helpful please
Related Articles RSS Feed
Bamboo water feature DIY
Viewed 12361 times since Wed, Oct 24, 2012
Build a garden scullery
Viewed 20504 times since Thu, Aug 29, 2013
Make a Sun Lounger
Viewed 5460 times since Thu, Aug 29, 2013
Build an outdoor shower
Viewed 10565 times since Thu, Mar 14, 2013
Fired up - making a portable fire
Viewed 9978 times since Fri, Sep 28, 2012
Building floating steps
Viewed 22536 times since Mon, Jan 27, 2014
Turn a ladder into a striking display unit
Viewed 11155 times since Mon, Oct 22, 2012
A tall Order - metal plant and light stand
Viewed 8398 times since Wed, Sep 26, 2012
Make A Table With Pots And Glass
Viewed 6610 times since Thu, May 17, 2012
Adirondack Patio Set
Viewed 4152 times since Fri, May 23, 2014